Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 13, 2010 7:45:28 GMT -8
Just a quick introduction to say hi. I'm from O'fallon, Missouri, USA.
I'm just a casual electronic hobbyist and discovered this site and forum. Lots of good stuff here!
I plan to start with the Anemometer circuit. I have an old Yamaha inline 4 cylinder motorcycle that I restored. Syncing the vacuum between the 4 carburetors is tedious for several reasons. Installing the two transistors into a tube running between vacuum ports would indicate simple air flow caused by any difference in vacuum between the two carbs being measured.
I'll post pics of the finished project.
Is the pcb board available for purchase? This would save a lot of work!
|
|
|
Post by Gary Lecomte on Mar 13, 2010 8:06:49 GMT -8
Just a quick introduction to say hi. I'm from O'fallon, Missouri, USA. I'm just a casual electronic hobbyist and discovered this site and forum. Lots of good stuff here! I plan to start with the Anemometer circuit. I have an old Yamaha inline 4 cylinder motorcycle that I restored. Syncing the vacuum between the 4 carburetors is tedious for several reasons. Installing the two transistors into a tube running between vacuum ports would indicate simple air flow caused by any difference in vacuum between the two carbs being measured. I'll post pics of the finished project. Is the pcb board available for purchase? This would save a lot of work! Yes the PCB is Available. Send me an Email with your Address and I'll send you one for FREE. Sounds like an Interesting Application! Gary
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 13, 2010 16:45:20 GMT -8
WOW! Email is on its way.
Thanks Gary.
|
|
|
Post by Gary Lecomte on Mar 14, 2010 15:53:20 GMT -8
WOW! Email is on its way. Thanks Gary. I Sent you Two Boards. Double the Pleasure and Double the Fun. (Or More Aggravation?) Enjoy....Gary
|
|
|
Post by Kees Krijnberg on Apr 26, 2016 7:17:50 GMT -8
Hello Gary, sorry for my english . I translate it using Google . I wanted to make the Anemometer and I are ready all the parts , but wanted to ask how I can get to the PCB board ? I 'm going to use the anemometer to: outside an Arduino with a 433Mhz transmitter when it is too windy to send a signal to my Raspberry Pi which retrieves the screens via Domoticz . Sincerely uit Nederland,
|
|
|
Post by Gary Lecomte on Apr 26, 2016 15:54:17 GMT -8
I wanted to make the Anemometer and I are ready all the parts , but wanted to ask how I can get to the PCB board ? I 'm going to use the anemometer to: outside an Arduino with a 433Mhz transmitter when it is too windy to send a signal to my Raspberry Pi which retrieves the screens via Domoticz . Sincerely uit Nederland.
The PCB is Available from me, But Unfortunately the Shipping costs to overseas are now quite expensive. And Legally Only PAPER can be sent in a Letter, So it is required to be Sent as a PARCEL with a Customs Declaration on it. So PCB is $2.00, But $9.00 Shipping Cost.
Also this Anemometer only works in LOW Speed Winds, (less than 5 Km/h)so Probably Not very Practical for your Application.
If I were to try to send it in a Letter, It MAY get to you and mailing cost is only $2.25. But how can you pay me?
On the other hand, If you still want the PCB, I'll mail it out to you in a Letter for Totally FREE. It's Light in weight, Small and Fairly Thin, so it will probably get to you OK
Just Email me With your Name and Address.
|
|
|
Post by topcase1 on Apr 27, 2016 4:29:22 GMT -8
Hi Gary, It is indeed a low wind speed , but I want to still like and want to use your offer to send it in an envelope . I'll send you an email with me and if you give a bank number to me by , I will transfer money to your bank. Very very cool. Thank you.
Kees
|
|
|
Post by Gary Lecomte on Apr 27, 2016 5:33:35 GMT -8
Hi Gary, It is indeed a low wind speed , but I want to still like and want to use your offer to send it in an envelope . I'll send you an email with me and if you give a bank number to me by , I will transfer money to your bank. Very very cool. Thank you. Kees It will be Mailed out Today, but it will take about 8 Business days to get to you. Receiving Bank Transfers Costs Money. Probably More than that $4.25 So Don't worry about the money.
|
|
|
Post by topcase1 on May 5, 2016 7:37:29 GMT -8
Hi Gary, It is indeed a low wind speed , but I want to still like and want to use your offer to send it in an envelope . I'll send you an email with me and if you give a bank number to me by , I will transfer money to your bank. Very very cool. Thank you. Kees It will be Mailed out Today, but it will take about 8 Business days to get to you. Receiving Bank Transfers Costs Money. Probably More than that $4.25 So Don't worry about the money. Hi Gary, The PCB is in! I think it's really great of you ! Again thank you very much! Topcase,
|
|